The Matek F722-PX-W Power Distribution Board (PDB) is specially designed to connect directly to the Matek F722-PX Flight Controller. This two combinations enable Fixed Wing usage for the latest F722-PX Pixel OSD FC. The PDB breaks out common ports and solder pads for servos and esc connections and connects via a ribbon cable to the flight controller.This board also uses the standard mounting hole patterns found in most Mini Quads and can also be used with other flight controllers, using solder pads to connect to the flight controller.
The Matek F722-PX-W Power Distribution Board (PDB) is specially designed to connect directly to the Matek F722-PX Flight Controller. This two combinations enable Fixed Wing usage for the latest F722-PX Pixel OSD FC. The PDB breaks out common ports and solder pads for servos and esc connections and connects via a ribbon cable to the flight controller.This board also uses the standard mounting hole patterns found in most Mini Quads and can also be used with other flight controllers, using solder pads to connect to the flight controller.
PRODUCT DESCRIPTION
PDB
Input voltage range: 9~30V (3~6S LiPo) w/TVS protection
2x ESC power pads
Current Sensor: 104A, 3.3V ADC, Scale 317
4x BEC on board
3x LED indicators for 5V, 10V & Vx
Soldering Holes & Pads
+ & – : Battery & ESC power pads
Curr: Current sensor output
Vbat: Battery voltage
G: Ground
3V3: LDO 3.3V
5V: BEC 5V
10V: BEC 10V
Vx: BEC 5V/6V/7.2V ADJ
FFC connection
Compatible with MATEKSYS FC F405-STD, F722-STD, F405-OSD
MT1: Motor1 of INAV Flying Wing & Airplane
MT2: Motor2 of INAV Flying Wing & Airplane
SV3~SV6: Servo 3~6 of INAV Flying Wing & Airplane
VTX: Video Transmitter signal
TX5 & RX5: UART5 of F405-STD/F722-STD/F405-OSD
BEC 5V output
Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, GPS module
DC/DC synchronous buck regulator
Voltage: 5.0 +/- 0.1VDC
Continuous current: 2 Amps, Max.3A
Output Ripple: 20mV (VIn=24V, VOut=5V@2A load)
Short-circuit tolerant (2 seconds)
BEC 10V output
Designed for Video Transmitter, Gimbal
DC/DC synchronous buck regulator
Voltage: 10.0 +/- 0.2VDC (Input voltage >11V)
Continuous current: 2 Amps, Max.3A
Output Ripple: 20mV (VIn=24V, VOut=10V@2A load)
Short-circuit tolerant (2 seconds)
BEC Vx output
Designed for Servos
DC/DC synchronous buck regulator
Voltage adjustable, 5V Default, 6V or 7.2V via jumper
Continuous current: 5 Amps, Max.5.5A
Output Ripple: 50mV (VIn=24V, VOut=5V@5A load)
Short-circuit tolerant (2 seconds)
BEC 3.3V output
Designed for Baro / Compass module and Spektrum RX
Linear Regulator
Continuous current: 500mA
Physical
Mounting: 30.5 x 30.5mm, Φ3mm
Dimensions: 52 x 36 x 6 mm
Weight: 13g
More Information
More Information
Manufacture
Matek Systems
Reviews
Write Your Own Review
What's this?Check "Remember Me" to access your shopping cart on this computer even if you are not signed in.