Toggle Nav
Search

BetaFPV SuperP 14CH ELRS Diversity Receiver

$29.99
Be the first to review this product
In stock

Introducing the groundbreaking SuperP 14CH Diversity Receiver! Engineered to excel in long-range flight and aerial photography, this receiver isn't limited to just these applications. Its versatility extends to fixed-wing aircraft, helicopters, RC cars, boats, and more. Featuring a precision TCXO oscillator, dual receiver chains, and two antennas, it also boasts Plug-N-Play ports and an array of additional functionalities. Supporting 14 channels for external barometers, RGB light strips, and other evolving sensors, this receiver anticipates future advancements. Available in 2.4GHz, 915MHz, and 868MHz versions, it meets the stringent reliability demands of long-range flying, aerial photography, and FPV freestyle maneuvers. Elevate your RC experience with enhanced stability and dependability courtesy of this exceptional receiver!

|

Details

FEATURES

  • Featuring 14 PWM channels, this receiver is suitable for different applications. It can drive up to 14 servos, allowing for more complex and precise control. In addition, an external sensor such as a barometer, current sensor, etc, is also supported.
  • A true diversity receiver with two complete RF receiver chains (referring to dual SX1280/SX1281 or dual SX1276), based on the latest official ExprssLRS. It comes with ExpressLRS V3.3 firmware.
  • Built in a TCXO (temperature-compensated crystal oscillator), it is shared by two RF chips for a super accurate clock source. It can withstand extreme temperatures with no fear of heat and cold, continuously outputting accurate frequency for long-range flight.
  • Two antennas will create an omnidirectional signal for good signal transmission. Placing the antenna separately and vertically to get a better signal is recommended.
  • With the support of the failsafe function, it is capable of protecting RC models from being out of control.
    Reserving a Type-C USB port, it is convenient for pilots to flash the firmware. The plug-and-play design makes it very easy and friendly to use.
  • The 900MHz radio system exhibits greater diffraction ability due to its lower frequency, while the 2.4GHz systems tend to be directional and susceptible to attenuation caused by buildings, foliage, or moisture.

 

Specification

  • Item: BETAFPV SuperP 14CH Diversity Receiver | ELRS 2.4GHz/915MHz/868MHz
  • MCU: ESP32 Pico D4 + 2*SX1280/SX1281 + 2*AT2401C (2.4GHz)
  • MCU: ESP32 Pico D4 + 2*SX1276（915MHz/868MHz）
  • Telemetry Power: 20dBm/100mW (2.4GHz), 17dBm/50mW (915MHz/868MHz)
  • Frequency Bands: 2.4GHz ISM, 915MHz FCC/868M EU
  • Rated Current: 180mA@5V (2.4GHz), 140mA@5V (915MHz/868MHz)
  • Weight: 15.5g (2.4GHz), 15.8g (915MHz/868MHz)
  • Default Firmware Version: ExpressLRS V3.3.0
  • Serial Output Protocol: PWM, CRSF or SBUS
  • Antenna: 2* IPEX MHF 1 Antenna
  • Size: 46.9mm*32.7mm*14.6mm
  • Voltage Detector Range: 1~6S
  • Input Voltage: 3.5V~8.4V DC
  • PWM Channel: 14 Channels
  • Adapted RC Model Type: Multirotors, Fixed-wing aircraft, Helicopters, RC Cars, RC Boats and etc.

Based on BETAFPV SuperD True Diversity Receiver and Micro Receiver, the SuperP 14CH Diversity Receiver takes the good features of them. For example, 14 PWM channels, two antennas, dual receiver chains, TCXO oscillator, etc. Besides, it has an I2C serial port for more external sensors such as a barometer, and a 3-pin port is reserved for RGB light strip. With the combination of the good points, SuperP RX ensures stability and reliability for users.

Compatible Models
The ExpressLRS receiver protocol can be widely used for more models such as multi-rotors, fixed-wing planes, helicopters, RC cars, RC Boats and etc. The two antennas and dual receiver chains design greatly fulfill the requirements for long-range flying and aerial photography.

It is recommended to place the antenna separately and vertically as far as possible for a better signal.

Binding Procedure
The default firmware of the SuperP 14CH Diversity Receiver uses the ExpressLRS V3.3.0 protocol and has no preset binding phrase. Therefore, the firmware version of the transmitter module must be ExpressLRS V3.0.0 or later versions. Both the receiver and transmitter module should not have any binding phrase.

Power on and off the receiver 3 times, each step pausing 2 seconds to enter binding mode;
When the indicator starts fast blink with orange twice, the receiving is at binding mode;
Enter the radio or transmitter module's binding mode to bind with the receiver; if the Indicator has turned solid, it indicates that the device has been bound successfully.